Product Carousel Tabs
20×4 Character LCD for RepRap Ramps 1.4
This 20×4 LCD board is used with the RAMPS 1.4 3D printer controller. You simply connect the LCD to the RAMPS board. This control unit has a built in SD card reader, rotary encoder as well as a 20×4 LCD display.
5V 10A Switching Power Supply
This is a high quality AC to DC switching power adapter which gives a clean regulated 5VDC output at up to 10A. These adapter works with both 110 and 240VAC input, allowing them to work in any country! The barrel plug attached to these wall adapters are center positive with 2.1mm diameter.
ESP8266 Grove WiFi Module
UART WiFi is a serial transceiver module featuring the ubiquitous ESP8266 IoT SoC. With integrated TCP/IP protocol stack, this module lets your microcontroller interact with WiFi networks with only a few lines of code. Each ESP8266 module comes pre-programmed with an AT command set firmware, meaning you can send simple text commands to control the device. The SoC features integrated WEP, WPA/WPA2, TKIP, AES, and WAPI engines, can act as an access point with DHCP, can join existing WiFi networks and has configurable MAC and IP addresses.
MAX31855 Type K Thermocouple Amplifier
Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. The MAX31855K does everything for you, and can be easily interfaced with any microcontroller, even one without an analog input. This breakout board has the chip itself, a 3.3V regulator with 10uF bypass capacitors and level shifting circuitry, all assembled and tested. Comes with a 2 pin terminal block (for connecting to the thermocouple) and pin header (to plug into any breadboard or perfboard).
MMA7260 & LISY300 – 6 DOF Atomic IMU
The 6DOF Atomic is a stripped-down IMU, designed to give good performance. The unit can run as a hard-wired UART interface (0-3.3V, 115200bps), or optionally with an XBee RF module, and is powered from a single LiPo (Lithium Polymer) battery. The processor is an Atmel ATMega328 running at 10MHz with 6 dedicated 10-bit ADC channels reading the sensors. Source code for the 6DOF Atomic is freely available and compiles with the free AVR GCC compiler.
Type K Thermocouple
Thermocouples are best used for measuring temperatures that can go above 100 Degree C. This is a bare wires bead-probe which can measure air or surface temperatures. Most inexpensive thermocouples have a vinyl covering which can melt at around 200 Degree C, this one uses a fiberglass braid so it can be used in high temperature measurements such as heaters and ovens. There’s a small piece of heat shrink on the end to keep the fiberglass from fraying. If you’re using at >250 Degree C temperatures, simply remove it with a small blade.
EC3 Connector Set
These connectors are made from high-temp nylon with gold-plated spring pins or sockets molded in. The shape of this generic EC3 prevents reverse polarity, and when plugged in the connection is super-solid. Perfect for applications up to 65A continuous draw. Sold in pairs of 1 male and 1 female connector.
12V Silicon Neon LED Strip – Green
This neon-like LED strip is super flexible and bendy, they feature a single-color non-addressable LED strip with a solid chunk of translucent silicone rubber as a diffuser. They look incredible, and super easy to use and are a great way to make your projects light up!
4 Pin (M-M) Jumper Wire
This jumper wire has a length of 450mm (18 inches) and comes with both male ends. The spacing pitch for the header is 2.54mm. This kind of flexible jumper wire is perfect for breadboard use as it fits perfectly in the breadboard.
3W High Power LED – Cool White
The 3W High Power LEDs are even brighter than standard incandescent and halogen light bulbs. Not only are they bright, they also consume a fraction of power making them extremely energy efficient! This high power LED is mounted onto an aluminium heat sink. Simply connect the large + and – pads on the heat sink to activate the LED. This high power LED is rated for 3.8V 700mA.
10 Pin Arduino Jumper Wire
10 Pin Arduino Jumper Wire
This is a special jumper wire specifically designed for the Arduino. This jumper wire adapts a 10 Pin Male Header which tightly fits into the Arduino pins and breaks it out into individual male jumper wires for you to attach to the breadboard or any other modules. These work much better than the individual jumper wires as they tend to fall apart after a while.
Force Sensitive Resistor – Square
This is a force sensitive resistor with a square, 1.75×1.5″, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR its resistance will be larger than 1Mohm. This FSR can sense applied force anywhere in the range of 100g-10kg. Two pins extend from the bottom of the sensor with 0.1″ pitch making it bread board friendly.
5mm to 5mm Flex Shaft Coupler
Connect this to that with a set-screw coupler. These couplers are made of machined aluminum and have a spiral cut that makes them slightly flexible so they can be fit to two shafts even if they are not perfectly co-linear and will help reduce binding effects. The way they’re cut, they’re a little springy in the X Y & Z linear axis but not in the rotational axis. That means that you won’t get increased backlash – so they’re suitable for precision CNC work. This coupler will connect a 5mm diameter shaft to an 5mm diameter shaft.