Product Carousel Tabs
20×4 Character LCD for RepRap Ramps 1.4
This 20×4 LCD board is used with the RAMPS 1.4 3D printer controller. You simply connect the LCD to the RAMPS board. This control unit has a built in SD card reader, rotary encoder as well as a 20×4 LCD display.
5V 10A Switching Power Supply
This is a high quality AC to DC switching power adapter which gives a clean regulated 5VDC output at up to 10A. These adapter works with both 110 and 240VAC input, allowing them to work in any country! The barrel plug attached to these wall adapters are center positive with 2.1mm diameter.
ESP8266 Grove WiFi Module
UART WiFi is a serial transceiver module featuring the ubiquitous ESP8266 IoT SoC. With integrated TCP/IP protocol stack, this module lets your microcontroller interact with WiFi networks with only a few lines of code. Each ESP8266 module comes pre-programmed with an AT command set firmware, meaning you can send simple text commands to control the device. The SoC features integrated WEP, WPA/WPA2, TKIP, AES, and WAPI engines, can act as an access point with DHCP, can join existing WiFi networks and has configurable MAC and IP addresses.
MAX31855 Type K Thermocouple Amplifier
Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. The MAX31855K does everything for you, and can be easily interfaced with any microcontroller, even one without an analog input. This breakout board has the chip itself, a 3.3V regulator with 10uF bypass capacitors and level shifting circuitry, all assembled and tested. Comes with a 2 pin terminal block (for connecting to the thermocouple) and pin header (to plug into any breadboard or perfboard).
MMA7260 & LISY300 – 6 DOF Atomic IMU
The 6DOF Atomic is a stripped-down IMU, designed to give good performance. The unit can run as a hard-wired UART interface (0-3.3V, 115200bps), or optionally with an XBee RF module, and is powered from a single LiPo (Lithium Polymer) battery. The processor is an Atmel ATMega328 running at 10MHz with 6 dedicated 10-bit ADC channels reading the sensors. Source code for the 6DOF Atomic is freely available and compiles with the free AVR GCC compiler.
Type K Thermocouple
Thermocouples are best used for measuring temperatures that can go above 100 Degree C. This is a bare wires bead-probe which can measure air or surface temperatures. Most inexpensive thermocouples have a vinyl covering which can melt at around 200 Degree C, this one uses a fiberglass braid so it can be used in high temperature measurements such as heaters and ovens. There’s a small piece of heat shrink on the end to keep the fiberglass from fraying. If you’re using at >250 Degree C temperatures, simply remove it with a small blade.
EC3 Connector Set
These connectors are made from high-temp nylon with gold-plated spring pins or sockets molded in. The shape of this generic EC3 prevents reverse polarity, and when plugged in the connection is super-solid. Perfect for applications up to 65A continuous draw. Sold in pairs of 1 male and 1 female connector.
9 Pin Polarized Wire Assembly
The polarized connectors are also referred to as Molex connectors. This polarized wire set comes with a polarized socket and a 20cm polarized wire with open ended wire leads. The polarized socket has pitch spacing of 2.54mm.
Sparkfun Digital Multimeter
The digital multimeter (DMM) is an essential tool in every electronic enthusiasts arsenal. The SparkFun Digital Multimeter, however, is not your average multimeter, it features a loud continuity sound, current/voltage sense, and quality probes. You can use the multimeter to measure DC and AC voltage, DC current, resistance, continuity, and test diodes. With this version we ve done away with the bright flashy colors that can get us into trouble and gone with a nice, neutral gray. This multimeter should provoke no strong feelings one way or the other, we know this because our guts say maybe.
5V 5A Switching Power Supply
This is a high quality AC to DC switching power adapter which gives a clean regulated 5VDC output at up to 5A. These adapter works with both 110 and 240VAC input, allowing them to work in any country! The barrel plug attached to these wall adapters are center positive with 2.1mm diameter.
WS2812 Addressable LED Ring Set (5 Pack)
There are a total of 61 WSS2812 RGB LEDs in this set. The 5 different WS2812 RGB LED rings are connected and can be de-attached to make 5 independent rings. The WS2812 LED driver chip allows these 5050 RGB LED to be independently addressed and controlled.
Note: The 5 rings are not electronically connected.