Accelerometer, Gyro & IMU

There are 19 products.

  • CAD$12.00 In Stock

    The ADXL335 is a triple axis MEMS accelerometer with extremely low noise and power consumption. The sensor has an analog output with full sensing range of +/-3g.

  • CAD$17.00 In Stock

    This ADXL345 module is low power 3-axis accelerometer, it uses I2C & SPI communication protocol where user can adjust the sensitivity and bit resolution. The ADXL345 is well suited to measure the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (4 mg/LSB)...

  • CAD$22.95 In Stock

    The ADXL362 is a complete 3-axis MEMS acceleration measurement system that operates at extremely low power consumption levels. It measures both dynamic acceleration, resulting from motion or shock, and static acceleration, such as tilt. It’s easy to communicate with the ADXL362 over SPI and built-in digital logic even enables autonomous operation for...

  • CAD$14.97 In Stock

    This triple-axis accelerometer is a carrier board for the Freescale MMA7341LC XYZ-axis accelerometer, a great low-g sensor with analog voltage outputs and adjustable sensitivity (±3 g or ±9 g), and a 0g-detect digital output that signals when the board is in free-fall (±3 g sensitivity setting only). The board has a 3.3V linear regulator that enables an...

  • CAD$10.50 Out of stock
    Out of stock

    This triple-axis accelerometer is a carrier board for the Freescale MMA7361LC XYZ-axis accelerometer, a great low-g sensor with analog voltage outputs and adjustable sensitivity (±1.5 g or ±6 g), and a 0g-detect digital output that signals when the board is in free-fall. The board has a 3.3V linear regulator that enables an input voltage range of 2.2-16...

  • CAD$12.50 In Stock

    The MMA8452Q is a smart low-power, three-axis, capacitive MEMS accelerometer with 12 bits of resolution. It is packed with embedded functions with flexible user programmable options, configurable to two interrupt pins. Embedded interrupt functions allow for overall power savings which relieves the host processor from continuously power consumption. It has...

  • CAD$21.50 In Stock

    This is a three axis accelerometer for the LilyPad system. Based on the ADXL335 MEMS accelerometer from Analog Devices, the LilyPad Accelerometer can detect joint movement as well as inclination and vibration. The ADXL335 outputs a 0V to 3V analog signal on each of the X, Y, and Z axis. You will need to convert this analog voltage to a gravity amount and...

  • CAD$25.95 In Stock

    Add motion and direction sensing to your wearable FLORA project with this high precision 3-axis Accelerometer+Compass sensor. Inside are two sensors, one is a classic 3-axis accelerometer, which can tell you which direction is down towards the Earth (by measuring gravity) or how fast the board is accelerating in 3D space. The other is a magnetometer that...

  • CAD$15.00 In Stock

    This sensor is a carrier/breakout board for the ST L3GD20 three-axis gyroscope, which measures the angular rates of rotation about the roll (X), pitch (Y), and yaw (Z) axes. Angular velocity measurements with a configurable range of ±250°/s, ±500°/s, or ±2000°/s can be read through a digital I²C or SPI interface. The board has a 3.3 V linear regulator and...

  • CAD$19.50 In Stock

    The L3G4200D has a full scale of +/-250 / +/-500 / +/-2000 dps which is capable of measuring rates with a user-selectable bandwidth. These work great in gaming and virtual reality input devices, GPS navigation systems and many other applications. There is also a downloadable Arduino Library which you can use to easily set the gyro up with your Arduino.

  • CAD$52.90 In Stock

    This is a breakout board for the L3G4200D low-power three-axis angular rate sensor. The L3G4200D is a MEMS motion sensor and has a full scale of ±250/±500/±2000 dps and is capable of measuring rates with a user-selectable bandwidth. These work great in gaming and virtual reality input devices, GPS navigation systems and robotics.

  • CAD$124.99 In Stock

    The 6DOF Atomic is a stripped-down IMU, designed to give good performance. The unit can run as a hard-wired UART interface (0-3.3V, 115200bps), or optionally with an XBee RF module, and is powered from a single LiPo (Lithium Polymer) battery. The processor is an Atmel ATMega328 running at 10MHz with 6 dedicated 10-bit ADC channels reading the sensors....

  • CAD$27.00 In Stock

    The MPU-6050 is a serious little piece of motion processing tech! By combining a MEMS 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an onboard Digital Motion Processor™ (DMP™) capable of processing complex 9-axis MotionFusion algorithms, the MPU-6050 does away with the cross-axis alignment problems that can creep up on...

  • CAD$27.50 In Stock

    The MinIMU-9 v3 is an inertial measurement unit (IMU) that packs an L3GD20H 3-axis gyro and an LSM303D 3-axis accelerometer and 3-axis magnetometer onto a tiny 0.8″ × 0.5″ board. An I²C interface accesses nine independent rotation, acceleration, and magnetic measurements that can be used to calculate the sensor’s absolute orientation. The MinIMU-9 v3...

  • CAD$16.50 In Stock

    The MPU-9250 IMU Breakout features the latest 9-axis MEMS sensor from InvenSense. The MPU-9250 combines both the MPU-6500 3-axis accelerometer and 3-axis gyroscope as well as the AKB963 3-axis magnetometer. 

  • CAD$48.00 In Stock

    If you've ever ordered and wire up a 9-DOF sensor, chances are you've also realized the challenge of turning the sensor data from an accelerometer, gyroscope and magnetometer into actual "3D space orientation"! Orientation is a hard problem to solve. The sensor fusion algorithms (the secret sauce that blends accelerometer, magnetometer and gyroscope data...

No products

To be determined Shipping
CAD$0.00 Total

Check out