Other Accessories

There are 19 products.

  • CAD$12.50 In Stock

    These cases protect the Arduino Uno Rev3 from things like rogue wires that might short it out while still allowing full access to the board. This enclosure is a must if you would like to protect your arduino!

  • CAD$12.99 In Stock

    These cases protect the Arduino Yun from things like rogue wires that might short it out while still allowing full access to the board. This enclosure is a must if you would like to protect your arduino!

  • CAD$11.80 In Stock

    This is a high quality AC to DC switching power adapter which gives a clean regulated 9VDC output at up to 1A. These adapter works with both 110 and 240VAC input, allowing them to work in any country! The barrel plug attached to these wall adapters are center positive with 2.1mm diameter.

  • CAD$2.00 In Stock

    This is a stanadard 9V battery snap with a 2.1mm DC barrel plug. This is perfect for powering your Arduino by batteries!

  • CAD$2.95 In Stock

    This is a standard 9V battery holder with a 2.1mm DC barrel plug. This is perfect for powering your Arduino by batteries!

  • CAD$4.95 In Stock

    This is a standard 9V battery enclosure with a 2.1mm DC barrel plug. This is perfect for powering your Arduino by batteries!  

  • CAD$4.25 In Stock

    This is a special jumper wire specifically designed for the Arduino. This jumper wire adapts a 6 Pin Male Header which tightly fits into the Arduino pins (A0 to A5) and breaks it out into individual male jumper wires for you to attach to the breadboard or any other modules. These work much better than the individual jumper wires as they tend to fall apart...

  • CAD$5.65 In Stock

    This is a special jumper wire specifically designed for the Arduino. This jumper wire adapts a 8 Pin Male Header which tightly fits into the Arduino pins (D0 to D7 or Power Pins) and breaks it out into individual male jumper wires for you to attach to the breadboard or any other modules. These work much better than the individual jumper wires as they tend...

  • CAD$7.25 In Stock

    This is a special jumper wire specifically designed for the Arduino. This jumper wire adapts a 10 Pin Male Header which tightly fits into the Arduino pins and breaks it out into individual male jumper wires for you to attach to the breadboard or any other modules. These work much better than the individual jumper wires as they tend to fall apart after a...

  • CAD$2.97 In Stock

    This is a set of 10 assorted colour jumper wires. Each jumper wire has a length of 150mm (6 inches) and comes with both male ends. This kind of flexible jumper wire is perfect for breadboard use as it fits perfectly in the breadboard.

  • CAD$2.98 In Stock

    This is a set of 10 assorted colour jumper wires. Each jumper wire has a length of 150mm (6 inches) and comes with one end male and one end female. This kind of flexible jumper wire is perfect for breadboard use as it fits perfectly in the breadboard.

  • CAD$2.99 In Stock

    This is a set of 10 assorted colour jumper wires. Each jumper wire has a length of 150mm (6 inches) and comes with both female ends. This kind of flexible jumper wire is perfect for breadboard use as it fits perfectly in the breadboard.

  • CAD$2.80 In Stock

    These headers are made to work with the Arduino Uno R3, Leonardo and new Arduino boards going forward. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers (2 8-pin, 1 10-pin and 1 6-pin), enough to connect a shield to an Arduino board.

  • CAD$3.30 In Stock

    These headers are made to work with the Arduino Uno R3, Leonardo and new Arduino boards going forward. The total height of the headers are 26mm with the pins at 12mm. This kit includes 5 headers (2 8-pin, 1 10-pin, 1 6-pin and 1 6-pin (2x3) ISP), enough to connect a shield to an Arduino board.   

  • CAD$0.86 In Stock

    This is a 6-pin female header, with extra long legs – great for stacking Arduino shields.

  • CAD$0.87 In Stock

    This is a 8-pin female header, with extra long legs – great for stacking Arduino shields.

No products

To be determined Shipping
CAD$0.00 Total

Check out