DC Gear Motor

There are 25 products.

  • CAD$23.00 In Stock

    This PWM controller can be used to adjust the duty of the PWM from 5% to 95%. You can hook up a load with a maximum of 4A to this controller. You can use this PWM controller for motor speed control as well as dimming high power LEDs.  

  • CAD$27.75 In Stock

    This PWM controller can be used to adjust the duty of the PWM from 10% to 100%. You can hook up a load with a maximum of 10A to this controller. You can use this PWM controller for motor speed control as well as dimming high power LEDs.  

  • CAD$7.90 In Stock

    This small circuit allows you to reverse the voltage applied to the load by simply pressing the switch. Typical applications are inverting the direction of DC motors or linear actuators. This voltage inverter can handle a maximum load of 5A @ 120VAC/28VDC.

  • CAD$37.50 In Stock

    This simple motor controller makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 30 V and is efficient enough to deliver a...

  • CAD$113.00 Out of stock
    Out of stock

    The powerful jrk 12v12 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-level serial, analog voltage, and hobby radio control (RC). The controller can be used as an open-loop speed control or for closed-loop speed or position control. The continuous output current is approximately 12 A...

  • CAD$6.80 In Stock

    This L9110 Dual Motor Driver is a motor driver breakout which can drive up to two DC motor at 2.5 to 12V with a maximum current at 800mA per channel.

  • CAD$12.00 In Stock

    This tiny board is an easy way to use Toshiba’s TB6612FNG dual motor driver, which can independently control two bidirectional DC motors or one bipolar stepper motor. A recommended motor voltage of 4.5 V to 13.5 V and peak current output of 3 A per channel (1 A continuous) make this a great motor driver for low-power motors.  

  • CAD$14.00 In Stock

    This L298 Dual Motor Driver is a motor driver breakout which can drive up to two DC motor at 7 to 24V with a maximum current at 2A per channel.

  • CAD$24.95 In Stock

    This breakout board for Freescale’s MC33926 full H-bridge has an operating range of 5 – 28 V and can deliver almost 3 A continuously (5 A peak) to a DC motor. The MC33926 works with 3 – 5 V logic levels, supports ultrasonic (up to 20 kHz) PWM, and features current feedback, under-voltage protection, over-current protection, and over-temperature protection.

  • CAD$56.95 In Stock

    This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The little 1.3×0.8-inch board supports a wide 5.5 to 50 V voltage range and is efficient enough to deliver a continuous 9 A without a heat sink.

  • CAD$48.50 In Stock

    This carrier board for ST’s VNH2SP30 motor driver IC operates from 5.5 to 16 V and can deliver a continuous 14 A (30 A peak). It works with 5 V logic levels, supports ultrasonic (up to 20 kHz) PWM, and features current sense feedback (an analog voltage proportional to the motor current). Along with built-in protection against reverse-voltage,...

  • CAD$49.95 In Stock

    This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The little 1.3×0.8-inch board supports a wide 5.5 to 30 V voltage range and is efficient enough to deliver a continuous 15 A without a heat sink.

  • CAD$79.99 In Stock

    This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The compact 1.8×1.2-inch board supports a wide 5.5 to 50 V voltage range and is efficient enough to deliver a continuous 20 A without a heat sink. This version outputs an analog voltage proportional to the motor current, and an extra control input...

  • CAD$75.99 In Stock

    This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The compact 1.8×1.2-inch board supports a wide 5.5 to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink. This version outputs an analog voltage proportional to the motor current, and an extra control input...

  • CAD$36.00 In Stock

    This BTN7960 Motor Driver is a high power motor driver breakout which can drive a DC motor at 6 to 27V with a maximum current at 43A. The BTS7960 also has built in overheating and overcurrent protections. 

  • CAD$16.25 In Stock

    This small shield is an easy, economical way to control two small brushed DC motors with an Arduino or Arduino-compatible board. Its integrated A4990 dual motor driver operates from 6 V to 32 V and can deliver a continuous 0.65 A to each motor channel, making it a great control option for low-current motors that run on high voltages. The A4990 is...

No products

To be determined Shipping
CAD$0.00 Total

Check out