Serial & USB Converter

There are 14 products.

  • CAD$13.00 In Stock

    This board is usefull to connect your PC to any digital board that uses a serial port with 3.3V or 5V level. Using a MAX3232C transceiver, this serial adapter can operate with 3,3V and 5V digital signals (it also accepts 5V logic inputs with 3,3V supply). It meets the requirements of TIA/EIA-232-F and provides the electrical interface between an...

  • CAD$9.25 In Stock

    This USB-to-serial adapter lets you easily connect a TTL serial device to a PC by acting as a virtual serial port. The board is a Micro-USB carrier for the Silicon Labs CP2104 USB-to-UART bridge that provides access to all of its control signal pins and GPIO pins.

  • CAD$18.50 In Stock

    The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USB<->Serial conversion chip and at the end of the 36" cable are four wire - red power, black ground, white RX into USB port, and green TX out of the USB port. The power pin provides the 5V @ 500mA direct from...

  • CAD$15.00 In Stock

    This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply.

  • CAD$29.75 In Stock

    This is the newest revision and fixes issues with the last board. This breakout board pairs an SP3485 RS-485 transceiver with an FT232RL USB UART IC to convert a USB stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps.

  • CAD$24.75 In Stock

    The FTDI Friend is a tweaked out FTDI FT232RL chip adapter. Sure, like the well-known FTDI cable, it can provide power to your project and there are 4 signal lines for sending data back and forth. But the Friend can do much more! For example, you can change the signal and power lines to be either 3.3V or 5V. Arduino-derivatives and XBees use the RTS line...

  • CAD$22.30 Out of stock
    Out of stock

    This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR...

  • CAD$21.55 In Stock

    Introducing the 3.3V SparkFun FT231X Breakout board, complete with the full UART hardware handshake feature! The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. This board still brings out the DTR pin as opposed to the RTS pin of the FTDI cable....

  • CAD$23.95 In Stock

    The XBee FTDI Adapter Mini USB is a compact USB to serial adapter equipped with BEE (20pin 2.0mm) sockets. This board uses the FT232RL IC for its functions. This board can be used as a FTDI to USB adapter for programming Arduino Pro Mini, as well as communicate data from the XBee transceivers to a USB device.

  • CAD$22.50 In Stock

    This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR...

  • CAD$25.50 In Stock

    The FTDI cable is a USB to Serial (TTL level) converter which allows for a simple way to connect TTL interface devices to USB. The VCC pins of this FTDI cable are configured to operate at 5V with 3.3V I/O.

  • CAD$25.50 In Stock

    The FTDI cable is a USB to Serial (TTL level) converter which allows for a simple way to connect TTL interface devices to USB. The I/O pins of this FTDI cable are configured to operate at 5V.

  • CAD$39.95 CAD$43.00 In Stock
    Reduced price!

    The Bus Pirate v3.6a is a troubleshooting tool that communicates between a PC and any embedded device over 1-wire, 2-wire, 3-wire, UART, I2C, SPI, and HD44780 LCD protocols - all at voltages from 0-5.5VDC. This product eliminates a ton of early prototyping effort when working with new or unknown chips.

  • CAD$37.50 In Stock

    The SPI Shortcut allows you to control SPI pins over USB, allowing for a virtual “SPI Terminal.” Using basic serial commands you can access any SPI device such as sensors, media, and even program some devices. You can change all of the SPI features (frequency, data order, etc.) on the fly with no programming involved! Comes with a simple-to-use terminal...

No products

To be determined Shipping
CAD$0.00 Total

Check out