Take a look at our selection of different Integrated Circuits here! – ICs, 4000, 74HC, 74LS, Amplifiers, Op-Amps, Optocouplers, Timers, Regulators and more…
Integrated Circuits
Showing 1–24 of 429 results
- Amplifiers
LMV358 Operational Amplifier Breakout
This is a simple 5V Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets the signal level between the stages, not the feedback path. The bandwidth is set to 15.9kHz by a pair of feedback capacitors, or over 100kHz with the caps removed. The LMV358 opamp can source up to 160mA and works well as a low impedance driver/buffer.
Part Number: PROOA-009816 - Logic ICs
74HC4067 8 Channel Multiplexer Breakout
The Multiplexer Breakout provides access to all pins and features of the 74HC4051, an 8-channel analog multiplexer/demultiplexer. The 74HC4051 allows you to turn four I/O pins into eight multifunctional, individually selectable signals, which can be used to do everything from driving eight LEDs to monitoring eight potentiometers.
Part Number: PROMX-009056 - Integrated Circuits
ATSHA204 Authentication Breakout
The Atmel ATSHA204 is an optimized authentication chip that includes a 4.5Kb EEPROM. This array can be used for storage of keys, miscellaneous read/write, read-only, password or secret data, and consumption tracking. Access to the various sections of memory can be restricted in a variety of ways and then the configuration locked to prevent changes.
Part Number: PROPC-011551 - Level Converters
BSS138 4 Channel Logic Level Translator
If you ve ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time.
Part Number: PROPC-012009 - Clocks & Timers, Raspberry Pi, Raspberry Pi Real Time Clocks
DS1307 Real Time Clock for Raspberry Pi
This RTC is designed specifically for the Raspberry where it uses the I2C communication pin on the GPIO pins of the Raspberry Pi. This module is based on the DS1307 real time clock chip uses the CR1220 coin cell battery for its operations. With this RTC the Raspberry Pi can remember the time even if the Raspberry Pi is powered off.
Part Number: RASPT-111307 - Clocks & Timers, Raspberry Pi, Raspberry Pi Real Time Clocks
DS3231 Real Time Clock for Raspberry Pi
This RTC is designed specifically for the Raspberry where it uses the I2C communication pin on the GPIO pins of the Raspberry Pi. This module is based on the DS3231 real time clock chip and uses the a coin cell battery for its operations. With this RTC the Raspberry Pi can remember the time even if the Raspberry Pi is powered off.
Part Number: RASPT-116001 - Level Converters
TXB0108 8 Channel Logic Level Translator
This breakout board provides eight bi-directional 3V/5V level translation channels, ideal for such things as SPI (e.g. SD card interface, MP3 chip interface) and port interfacing. The 20-pin TSSOP level shifter chip is mounted on a carrier and fits a standard 0.6″ wide DIP footprint.
Part Number: PROPC-000328 - Analog & Digital Converters
ADS1115 – 16 Bit I2C ADC Module
The ADS1115 is a 16-bit high precision, 860 samples/second analog to digital converter which interfaces though I2C. This ADC can be configured as 4 single-ended input channels or 2 differential channels. There is a programmable gain amplifier built in which can amplify up to 16 times the signal.
Part Number: PROAD-001086 - Analog & Digital Converters
ADS1118 – 16 Bit I2C ADC Module
The ADS1118 is a 16-bit high precision ADC with internal reference and temperature sensor.. This ADC can be configured as 4 single-ended input channels or 2 differential channels. This ADC can be interfaced though SPI with an operating voltage between 2V to 5V.
Part Number: PROAD-001118 - Analog & Digital Converters
MCP4725 – 12 Bit I2C DAC Module
This breakout board features the easy-to-use MCP4725 12-bit DAC. Control it via I2C and send it the value you want it to output, and the VOUT pin will have it. Great for audio / analog projects, such as when you can’t use PWM but need a sine wave or adjustable bias point.
Part Number: PRODA-004725 - Analog & Digital Converters
PCF8591 – 8 Bit I2C ADC & DAC Module
Have you ever wanted more analog input pins on your Arduino project, but not wanted to fork out for a Mega Or would you like to generate analogue signals It solves both these problems as it has a single DAC (digital to analogue) converter as well as four ADCs (analogue to digital converters), all accessible via the I2C bus. If the I2C bus is new to you, please familiarise yourself with the readings here before moving forward.
Part Number: PRODA-008591 - Clocks & Timers
DS1307 Real Time Clock Module
This real time clock module is based on the DS1307 chip which supports the I2C protocol. The clock and calendar provides seconds, minutes, hours, day, date, month, and year information. The end of the month date is automatically adjusted for months with fewer than 31 days, including corrections for leap year. The clock operates in either a 24-hour or 12-hour format with AM/PM indicator.
Note: CR2032 Coin Cell Batteryis not included.
Part Number: PRORT-001101 - Clocks & Timers
DS3231 Real Time Clock Module
The DS3231 is an extremely accurate I2C real-time clock with an integrated temperature-compensated crystal oscillator (TCXO) and crystal. The DS3231 function with a VCC ranging from 2.3V to 5.5V. In comparison to the DS1307, the DS3231 has an integrated crystal, temperature sensor, 2 programmable time-of-day alarms, a 32.768 kHz output pin to ensure higher accuracy.
Note:The CR2032coin cell battery is not included.
Part Number: PRORT-003231 - Clocks & Timers
NE555 Pulse Generator
The NE555 timer IC is often used for timers, pulse generations, and oscillator applications. This NE555 frequency adjustable pulse generator module utilizes the NE555 timer IC to generate sqaure wave pulses from 1Hz to 200KHz, which can be used for experimental electronic development.
Part Number: PRORT-077555 - Clocks & Timers
Electronic Time Delay Module
This time delay module provides you a way to delay and control the time of a signal. With this module, you can set a delay time of 0 to 14 minutes with the onboard potentiometer. You can set the module start/stop timing, which makes it convenient in electronic projects.
Part Number: PROTD-000014 - Clocks & Timers, Feather, Integrated Circuits
RTC & SD Adalogger FeatherWing
A Feather board without ambition is a Feather board without FeatherWings! This is the Adalogger FeatherWing: it adds both a battery-backed Real Time Clock and micro SD card storage to any Feather main board.
Part Number: FEATH-002922 - Integrated Circuits, Clocks & Timers, Feather
DS3231 Precision RTC FeatherWing
A Feather board without ambition is a Feather board without FeatherWings! This is the DS3231 Precision RTC FeatherWing: it adds an extremely accurate I2C-integrated Real Time Clock (RTC) with a Temperature Compensated Crystal Oscillator (TCXO) to any Feather main board. This RTC is the most precise you can get in a small, low power package.
Part Number: FEATH-003028