Bracket & Attachment

There are 62 products.

  • CAD$29.95 In Stock

    This mini gripper is a small-volume, simple gripper perfect for "getting a grip" in lightweight projects. Made of light-weight acrylic material, this gripper also equipped with a 9g servo which ensures fast gripping speed. This mini gripper is suggested to use in lightweight projects. It is perfect to grab and carry small items with the diameter between...

  • CAD$140.00 Out of stock
    Out of stock

    Makeblock Robotic Arm Add-on Pack is a robot pack to expand upon your Makeblock Starter Robot Kit. It contains  all the parts to build the robotic arm such as DC Motor-37, Robot Gripper, beams, timing pulleys and hardware.

  • CAD$9.75 In Stock

    This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism using two servo motors.

  • CAD$23.00 In Stock

    This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism using any two servo motors.

  • CAD$5.90 In Stock

    This 18" (45 cm) harness has an inline on/off switch, with a 0.1" 3-pin female connector on one end and both a male and a female connector on the other. This 3-wire harness can be used to add a toggle switch between any two devices that can be connected with “JR” style servo connectors. One side of the switch has a lead with a female connector, while the...

  • CAD$2.40 In Stock

    This set of gears contains 40, 30, 20 and 12 tooth gears and 3 bushings. The 12 tooth motor spindle has a hole diameter of 2mm, where the 40, 30, 20 tooth gears all have a hole diameter of 3/16".

  • CAD$2.40 In Stock

    This set of gears contains 40, 30, 20 and 12 tooth gears and 3 bushings. The 12 tooth motor spindle has a hole diameter of 2mm, where the 40, 30, 20 tooth gears all have a hole diameter of 3/16".

  • CAD$2.40 In Stock

    This set of gears contains 40, 30, 20 and 12 tooth gears and 3 bushings. The 12 tooth motor spindle has a hole diameter of 2mm, where the 40, 30, 20 tooth gears all have a hole diameter of 3/16".

  • CAD$14.50 In Stock

    Add quadrature encoders to your micro metal gearmotors (extended back shaft version required) with this kit consisting of two sensor boards, two 3-tooth encoder wheels, and two 5-tooth encoder wheels. The installed system does not exceed the 12 mm × 10 mm cross section of the motors and extends only 5 mm beyond the plastic motor end cap. The 3-tooth wheel...

  • CAD$16.50 In Stock

    This is a 2 channel optical encoder set what fits perfectly with our 2WD and 4WD robot platforms! This kit will help you monitor the speed of the motors. This encoder set uses the HC-020 to optically sense the rotation of the circular grid board which will output a square wave signal. There 20 grids on the circular grid board, so each rising/falling edge...

  • CAD$36.00 In Stock

    This "Incremental quadrature encoder system" is specially designed by Nubotics to retrofit to our GM2, GM3, GM8 or GM9 gear motor. If you need to control a robot for dead reckoning, tracking odometry (distance travelled), stalled motor, or closing the feedback loop for position/velocity/acceleration, this is your solution.

  • CAD$1.20 In Stock

    This acrylic grid board can be used with our 120:1 Gear Motor (5V 83PM) and Optical Encoder Set for DC Gear Motor. 

  • CAD$6.00 In Stock

    These fine drive belt are made with rubber which can be used as engine drive belts for small DIY cars. This pack of drive belt consists of an assortment of 30mm to 120mm belts.

  • CAD$4.00 Out of stock
    Out of stock

    Timing belts are a fantastic way to transfer rotational motion into linear motion and these GT2 belts are excellent for the task. Often used for precision 3D printers and CNC machines. This belt is 280mm in length and 6mm in width with 2mm pitch. It comes in a loop but you can of course cut it down if you need a shorter length.

  • CAD$21.50 In Stock

    Timing belts are a fantastic way to transfer rotational motion into linear motion and these GT2 belts are excellent for the task. Often used for precision 3D printers and CNC machines. This belt is 1164mm long with 2mm pitch and 6mm wide. It comes in a loop but you can of course cut it down if you need a shorter length.

  • CAD$19.00 In Stock

    Timing belts are a fantastic way to transfer rotational motion into linear motion and these GT2 belts are excellent for the task. Often used for precision 3D printers and CNC machines. This belt is 2004mm long with 2mm pitch and 6mm wide. It comes in a loop but you can of course cut it down if you need a shorter length.

No products

To be determined Shipping
CAD$0.00 Total

Check out