Motor Driver

There are 45 products.

  • CAD$14.00 In Stock

    The A4988 Stepper Motor Driver is a microstepping bipolar stepper motor driver. The A4988 Stepper Moto Driver is able to drive a stepper motor from 8 to 35V with a continuous current of 1A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient additional cooling). This A4988 driver also features adjustable current...

  • CAD$14.25 In Stock

    Black Edition A4988 stepper motor driver carrier is a higher-performance drop-in replacement for the original A4988 stepper motor driver carrier. It features a four-layer PCB for better thermal performance, allowing the A4988 microstepping bipolar stepper motor driver to deliver approximately 20% more current than our two-layer (green) version. Like our...

  • CAD$14.25 In Stock

    This breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver features adjustable current limiting, over-current and over-temperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 V to 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2...

  • CAD$10.50 In Stock

    This is a breakout board for TI’s DRV8834 microstepping bipolar stepper motor driver. It has a pinout and interface that are nearly identical to those of our A4988 carriers, so it can be used as a drop-in replacement for those boards in many applications. The DRV8834 operates from 2.5–10.8 V, allowing stepper motors to be powered with voltages that are...

  • CAD$13.00 In Stock

    The EasyDriver is a simple to use stepper motor driver that can driver up to about 750mA per phase of a bi-polar stepper motor. EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire...

  • CAD$24.95 In Stock

    Each Big Easy Driver can drive up to a max of 2A per phase of a bi-polar stepper motor. It is a chopper microstepping driver which defaults to 16 step microstepping mode. It can take a maximum motor drive voltage of around 30V, and includes on-board 5V/3.3V regulation, so only one supply is necessary. Although this board should be able to run most systems...

  • CAD$5.15 In Stock

    This ULN2003 Unipolar Stepper Motor Driver uses the ULN2003 darlington transistor array to drive a unipolar stepper motor. The ULN2003 driver can drive between 5 to 12V at 0.5A per phase.

  • CAD$35.95 In Stock

    The CNC Shield makes it really simple to integrate CNC projects with the Arduino. You can add up to 4x A4988 stepper motor drivers to the CNC shield allowing for independent control of 4 bi-polar stepper motors. 

  • CAD$35.95 In Stock

    The RAMPS (RepRap Arduino Mega Pololu Shield) is an all-in-one design to fit the necessary components for a 3D printer into one plug in shield. The plug in shield design includes plug in stepper drivers and extruder control electronics sockets for easy service, part replacement, upgrade-ability and expansion. Ramps boards are the heart of most DIY 3D...

  • CAD$23.00 In Stock

    This PWM controller can be used to adjust the duty of the PWM from 5% to 95%. You can hook up a load with a maximum of 4A to this controller. You can use this PWM controller for motor speed control as well as dimming high power LEDs.  

  • CAD$27.75 In Stock

    This PWM controller can be used to adjust the duty of the PWM from 10% to 100%. You can hook up a load with a maximum of 10A to this controller. You can use this PWM controller for motor speed control as well as dimming high power LEDs.  

  • CAD$7.90 In Stock

    This small circuit allows you to reverse the voltage applied to the load by simply pressing the switch. Typical applications are inverting the direction of DC motors or linear actuators. This voltage inverter can handle a maximum load of 5A @ 120VAC/28VDC.

  • CAD$6.80 In Stock

    This L9110 Dual Motor Driver is a motor driver breakout which can drive up to two DC motor at 2.5 to 12V with a maximum current at 800mA per channel.

  • CAD$12.00 In Stock

    This tiny board is an easy way to use Toshiba’s TB6612FNG dual motor driver, which can independently control two bidirectional DC motors or one bipolar stepper motor. A recommended motor voltage of 4.5 V to 13.5 V and peak current output of 3 A per channel (1 A continuous) make this a great motor driver for low-power motors.  

  • CAD$14.00 In Stock

    This L298 Dual Motor Driver is a motor driver breakout which can drive up to two DC motor at 7 to 24V with a maximum current at 2A per channel.

  • CAD$37.50 In Stock

    This simple motor controller makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 30 V and is efficient enough to deliver a...

No products

To be determined Shipping
CAD$0.00 Total

Check out