Motors
Showing 25–48 of 208 results
- 3D Printing, Motors, Stepper Motors
NEMA-17 Bipolar Stepper Motor with Lead Screw (28cm)
This NEMA 17-size bipolar stepping motor has a lead screw of 280mm with a 1.8 Degree step angle (200 steps/revolution). Both the stepper motor and the brass flange are equiped with M3 threads.
Part Number: MOTOR-222267 - Motors, Vibration Motors
Mini Vibration Motor – 10mm
These vibe motors are tiny discs, completely sealed up so they’re easy to use and embed. Two wires are used to control/power the vibe. Simply provide power from a battery or microcontroller pin (red is positive, blue is negative) and it will buzz away. Works from 2V up to 5V, higher voltages result in more current draw but also a stronger vibration.
Part Number: SPEDE-001201 - Motors, Vibration Motors
Vibration Motor
This tiny DC motor has a shaft with an offset mass that vibrates when it rotates. Motors like this are commonly found in cell phones and other devices that use vibration for tactile feedback. The motor has 1.5 leads and is encased in a removable rubber sleeve that gives it flat surfaces for mounting and prevents it from chattering against whatever it is mounted to. It is intended for operation around 3 V (2.4 V to 3.5 V recommended).
Part Number: SPEDE-002265 - Motors, Solenoids
5V Mini Pull Type Solenoid
Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers. This smaller solenoid is designed to work directly with 5V which makes it a great match for embedded projects. It has a throw of about 4.5mm and 2 M2 mounting holes on the body.
Part Number: USOLE-511015 - Motors, Solenoids
12V Pull Type Solenoid (6mm)
Open Frame Solenoids are a basic, opened-coil type of linear motion solenoids. Due to their simpledesign structure, they are less costly, and are offered in a wide variety of sizes and types to bestmeet your application requirements.
Part Number: USOLE-081500 - Motors, Solenoids
12V Pull Type Solenoid (10mm)
Open Frame Solenoids are a basic, opened-coil type of linear motion solenoids. Due to their simpledesign structure, they are less costly, and are offered in a wide variety of sizes and types to bestmeet your application requirements.
Part Number: USOLE-413529 - Motors, Solenoids
12V Push Pull Solenoid
This solenoid in particular is fairly small, with a 30mm long body and a ‘captive’ armature with a return spring. This means that when activated with up to 24VDC, the solenoid moves and then the voltage is removed it springs back to the original position, which is quite handy. Many lower cost solenoids are only push type or only pull type and may not have a captive armature (it’ll fall out!) or don’t have a return spring. This one even has nice mounting tabs, its a great all-purpose solenoid.
Part Number: USOLE-412300 - Motors, Solenoids
12V Large Push Pull Solenoid
This solenoid in particular is nice and strong, with a 40mm long body and a ‘captive’ armature with a return spring. This means that when activated with up to 24VDC, the solenoid moves and then the voltage is removed it springs back to the original position, which is quite handy. Many lower cost solenoids are only push type or only pull type and may not have a captive armature (it’ll fall out!) or don’t have a return spring. This solenoid has 4xM3 (metric) threaded holes in the bottom for easy mounting.
Part Number: USOLE-413300 - Motors, Solenoids
12-36V Large Push Pull Solenoid
Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers. According to the datasheet this solenoid is rated for 36V but they work like a charm at 12V. We ve been controlling them with the Arduino Power Driver Shield, there s even some example code below. With a throw of 10mm these solenoids are great for all kinds of motion applications such as actuating door latches, automating percussion instruments or just poking people.
Part Number: USOLE-610391 - Motors, Solenoids
9-12V Mini Locking Solenoid
The tongue of the solenoid pops up when power is applied, as the internal coil generates a magnetic force to attract the tongue. This mini locking solenoid is perfect for locking a door or any mechanism. It has a quick respond time of just one second.
Part Number: USOLE-001035 - Motors, Solenoids
9-12V Locking Solenoid
This solenoid in particular is nice and strong, which has a slug with a slanted cut and a good mounting bracket. It’s basically an electronic lock, designed for a cabinet, safe, and door. Normally the lock is active so you can’t open the door because the solenoid slug is in the way. It does not use any power in this state. When 9-12VDC is applied, the slug pulls in so it doesn’t stick out anymore and the door can be opened.
Part Number: USOLE-001512 - Motors, Solenoids
12V Linear Actuator – 300mm
The casting of these Linear Actuators are completely sealed from the manufacturer with an IP54 degree dust and water vapor protection. These linear actuators uses a worm drive to move the shaft up back and forth along its length. The worm drive ensures that the shaft will hold its position even when unpowered. Two limit switches safely stop the motor at either end of its range, while diodes allow it to reverse direction after reaching a limit point.
Part Number: LINAR-001035 - Motors, Air & Water Pumps
12V Liquid Pump – 22L/min
Do you have some liquids that you need to move This fluid pump will move 350 gallons per hour! The SEAFLO mini water pump has a heavy duty 12V, 1.5Amp motor and a tough thermoplastic body. It s totally submersible and water-cooled (but it won t burn out if run dry). Use this pump to make a fountain or waterfall, even water your plants!
Part Number: MOTOR-510455 - Motors, Fans & Blowers
5V DC Brushless Fan – 30x30x10mm
This is a small 30 x 30 x 10mm fan. The fan has a DC brushless motor, with an operating voltage of 5V, and is rated at 130mA. The screw thread for mounting this fan are M3 which is great as they are very popular! Keeping the temperature down in your project can often be a necessity, and this fan can definitely help!
Part Number: UNFAN-005013 - Motors, Fans & Blowers
12V DC Brushless Fan – 30x30x10mm
This is a smaller 30 x 30 x 10mm fan. The fan has a DC brushless motor, with an operating voltage of 12V, and is rated at 80mA. Keeping the temperature down in your project can often be a necessity, and this fan can definitely help!
Part Number: UNFAN-012014 - Motors, Fans & Blowers
12V DC Brushless Fan – 40x40x10mm
This is a smaller 40 x 40 x 10mm fan. The fan has a DC brushless motor, with an operating voltage of 12V, and is rated at 100mA. Keeping the temperature down in your project can often be a necessity, and this fan can definitely help!
Part Number: UNFAN-004040 - Motors, Fans & Blowers
12V DC Brushless Fan – 80x80x15mm
This is a fairly large, 80 x 80 x 15mm fan. The fan has a DC brushless motor, with an operating voltage of 12V, and is rated at 250mA. Keeping the temperature down in your project can often be a necessity, and this fan can definitely help.
Part Number: UNFAN-008080