Take a look at our selection of different Stepper Motors here! – Bipolar Stepper Motors, Unipolar Stepper Motors, NEMA16, NEMA17, NEMA23, 3V, 5V, 6V, 9V, 12 and more…
Stepper Motors
Showing all 24 results
- Motors, Stepper Motors
Hobby Unipolar Stepper Motor
These small steppers are a great way to get things moving, especially when positioning and repeatability is a concern.
Note: This is a Unipolar stepper, meaning that if you are going to drive it with a bipolar stepper driver, you will only use 4 of the 6 leads.
Part Number: MOTOR-412805 - Motors, Stepper Motors
NEMA-8 Bipolar Stepper Motor (0.18kg-cm)
This small NEMA 8-size hybrid bipolar stepping motor has a 1.8 Degree step angle (200 steps/revolution). Each phase draws 600 mA at 3.9 V, allowing for a holding torque of 180 g-cm (2.5 oz-in). With a weight of 60 g, this is one of the smallest stepper motors we carry.
Part Number: MOTOR-111204 - Motors, Stepper Motors
NEMA-23 Unipolar Stepper Motor (4kg-cm)
This NEMA 23-size hybrid stepping motor can be used as a unipolar or bipolar stepper motor and has a 1.8 Degree step angle (200 steps/revolution). Each phase draws 1 A at 5.7 V, allowing for a holding torque of 4 kg-cm (55 oz-in).
Part Number: MOTOR-111476 - 3D Printing, Motors, Stepper Motors
NEMA-17 Bipolar Stepper Motor with Lead Screw (28cm)
This NEMA 17-size bipolar stepping motor has a lead screw of 280mm with a 1.8 Degree step angle (200 steps/revolution). Both the stepper motor and the brass flange are equiped with M3 threads.
Part Number: MOTOR-222267 - Motors, New Products, Stepper Motors
T500 Tic USB Stepper Motor Driver
The Tic T500 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC). This version incorporates an MPS MP6500 driver, and male headers and terminal blocks are included but not soldered. It can operate from 4.5 V to 35 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (or 2.5 A max with sufficient additional cooling).
Part Number: PROMR-003135 - Motors, Stepper Motors
EasyDriver Stepper Motor Driver v4.4
The EasyDriver is a simple to use stepper motor driver that can driver up to about 750mA per phase of a bi-polar stepper motor. EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you’ve got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors. It is a chopper microstepping driver based on the Allegro A3967 driver chip, The microstep select (MS1 and MS2) pins of the A3967 are broken out allowing adjustments to the microstepping resolution. The sleep and enable pins are also broken out for further control.
Part Number: PROMR-010263 - Motors, Stepper Motors
Big Easy Driver Stepper Motor Driver
Each Big Easy Driver can drive up to a max of 2A per phase of a bi-polar stepper motor. It is a chopper microstepping driver which defaults to 16 step microstepping mode. It can take a maximum motor drive voltage of around 30V, and includes on-board 5V/3.3V regulation, so only one supply is necessary. Although this board should be able to run most systems without active cooling while operating at 1.4-1.7A/phase, a heatsink is required for loads approaching 2A/phase.
Part Number: PROMR-011876 - 3D Printing, Motors, Stepper Motors
A4988 Stepper Motor Driver – 2A
The A4988 is a complete microstepping motor driver with a built-in translator for easy operation. The A4988 has 5 modes including full, half, 1/4, 1/8 and 1/16 steps. The driver is able to operate any bipolar stepper motor with an output up to 35V 2A.
Note: This is an A4988 stepper motor driver and is not a product from Pololu Robotics & Electronics.
Part Number: DDDMR-004988 - 3D Printing, Motors, Stepper Motors
A4988 Stepper Motor Driver Black Edition – 2A
Black Edition A4988 stepper motor driver carrier is a higher-performance drop-in replacement for the original A4988 stepper motor driver carrier. It features a four-layer PCB for better thermal performance, allowing the A4988 microstepping bipolar stepper motor driver to deliver approximately 20% more current than our two-layer (green) version. Like our original carrier, the Black Edition offers adjustable current limiting, over-current and over-temperature protection, and five different microstep resolutions. It operates from 8 V to 35 V and can deliver up to 2 A per coil with sufficient additional cooling.
Part Number: PROMR-002129 - 3D Printing, Motors, Stepper Motors
DRV8825 Stepper Motor Driver – 2.2A
The DRV8825 is a complete microstepping motor driver with features such as adjustable current limiting and over-current & temperature protection. The A4988 has 6 microsteping resolution and operates from 8.5 to 45V and can deliver 1.5A per phase without additional cooling.
Note: This is a DRV8825 stepper motor driver and is not a product from Pololu Robotics & Electronics.
Part Number: PROMR-002133 - Motors, Stepper Motors
DRV8834 Low Voltage Stepper Motor Driver – 2A
This is a breakout board for TI s DRV8834 microstepping bipolar stepper motor driver. It has a pinout and interface that are nearly identical to those of our A4988 carriers, so it can be used as a drop-in replacement for those boards in many applications. The DRV8834 operates from 2.5 10.8 V, allowing stepper motors to be powered with voltages that are too low for other drivers, and can deliver up to approximately 1.5 A per phase continuously without a heat sink or forced air flow (up to 2 A peak). It features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step).
Part Number: PROMR-008834 - Motors, Stepper Motors
ULN2003 Unipolar Stepper Motor Driver – 0.5A
This stepper motor driver uses the ULN2003 darlington transistor array. The motor driver can drive a unipolar stepper motor between 5 to 12V at 0.5A per phase. There are also 4 LED indicators to indicate the status of the motor.
Part Number: MOTOR-412846 - Arduino, Arduino Motor Drivers, Microcontrollers, Motors, Gear Motors, Servo Motors, Stepper Motors
4 Channel Motor Shield – 1.2A
Arduino, Arduino Motor Drivers, Microcontrollers, Motors, Gear Motors, Servo Motors, Stepper Motors4 Channel Motor Shield – 1.2A
This motor driver shield can drive up to 4 DC motor with 2 servo motors or 2 stepper motors with 2 servo motors. This motor driver shield uses 2x L293D motor controller chip with a 74HC595 shift register for all of its functions.
Part Number: ARDME-002930 - 3D Printing, Arduino, Arduino Motor Drivers, Microcontrollers, Motors, Stepper Motors
CNC Shield v3.51
3D Printing, Arduino, Arduino Motor Drivers, Microcontrollers, Motors, Stepper MotorsCNC Shield v3.51
The CNC Shield makes it really simple to integrate CNC projects with the Arduino. You can add up to 4x A4988 stepper motor drivers to the CNC shield allowing for independent control of 4 bi-polar stepper motors.
Part Number: ARDCE-005510 - Arduino, Arduino Motor Drivers, Gear Motors, Microcontrollers, Motors, Servo Motors, Stepper Motors
ComMotion 4 Channel Motor Shield – 4A
Arduino, Arduino Motor Drivers, Gear Motors, Microcontrollers, Motors, Servo Motors, Stepper MotorsComMotion 4 Channel Motor Shield – 4A
This is the ComMotion Motor Driver Shield, a 4 channel motor controller that can communicate via I2C and be wirelessly controlled. This shield allows you to be able to control up to 4 motors at a time, read their encoders, and monitor their current draw all from one board. This powerful little shield fits snuggly on top of your RedBoard, Arduino, or any other development board that utilizes the R3 layout.
Part Number: PROMR-013257 - 3D Printing, Arduino, Arduino Motor Drivers, Microcontrollers, Motors, Stepper Motors
RAMPS 1.4 for 3D Printer
3D Printing, Arduino, Arduino Motor Drivers, Microcontrollers, Motors, Stepper MotorsRAMPS 1.4 for 3D Printer
The RAMPS (RepRap Arduino Mega Pololu Shield) is an all-in-one design to fit the necessary components for a 3D printer into one plug in shield. The plug in shield design includes plug in stepper drivers and extruder control electronics sockets for easy service, part replacement, upgrade-ability and expansion. Ramps boards are the heart of most DIY 3D printers on the market and a nice clean compact way to integrate all the systems into a compact enclosure mountable format.
Part Number: DDDAE-000914 - Motors, Gear Motors, Servo Motors, Stepper Motors, Raspberry Pi, Raspberry Pi Motor Drivers
4 Channel Motor Hat for Raspberry Pi – 1.2A
Motors, Gear Motors, Servo Motors, Stepper Motors, Raspberry Pi, Raspberry Pi Motor Drivers4 Channel Motor Hat for Raspberry Pi – 1.2A
This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Since the Raspberry Pi does not have a lot of PWM pins, we use a fully-dedicated PWM driver chip onboard to both control motor direction and speed. This chip handles all the motor and speed controls over I2C. Only two pins (SDA & SCL) are required to drive the multiple motors, and since it’s I2C you can also connect any other I2C devices or HATs to the same pins.
Part Number: RASPB-002348 - Feather, Motors, Gear Motors, Stepper Motors
4 Channel Motor FeatherWing – 1.2A
A Feather board without ambition is a Feather board without FeatherWings! This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top or bottom of your Feather board and let the board take flight!
Part Number: FEATH-002927