Pulley & Attachment

There are 22 products.

  • CAD$16.50 In Stock

    This is a 2 channel optical encoder set what fits perfectly with our 2WD and 4WD robot platforms! This kit will help you monitor the speed of the motors. This encoder set uses the HC-020 to optically sense the rotation of the circular grid board which will output a square wave signal. There 20 grids on the circular grid board, so each rising/falling edge...

  • CAD$1.20 In Stock

    This acrylic grid board can be used with our 120:1 Gear Motor (5V 83PM) and Optical Encoder Set for DC Gear Motor. 

  • CAD$14.50 In Stock

    Add quadrature encoders to your micro metal gearmotors (extended back shaft version required) with this kit consisting of two sensor boards, two 3-tooth encoder wheels, and two 5-tooth encoder wheels. The installed system does not exceed the 12 mm × 10 mm cross section of the motors and extends only 5 mm beyond the plastic motor end cap. The 3-tooth wheel...

  • CAD$36.00 In Stock

    This "Incremental quadrature encoder system" is specially designed by Nubotics to retrofit to our GM2, GM3, GM8 or GM9 gear motor. If you need to control a robot for dead reckoning, tracking odometry (distance travelled), stalled motor, or closing the feedback loop for position/velocity/acceleration, this is your solution.

  • CAD$2.40 In Stock

    This set of gears contains 40, 30, 20 and 12 tooth gears and 3 bushings. The 12 tooth motor spindle has a hole diameter of 2mm, where the 40, 30, 20 tooth gears all have a hole diameter of 3/16".

  • CAD$2.40 In Stock

    This set of gears contains 40, 30, 20 and 12 tooth gears and 3 bushings. The 12 tooth motor spindle has a hole diameter of 2mm, where the 40, 30, 20 tooth gears all have a hole diameter of 3/16".

  • CAD$2.40 In Stock

    This set of gears contains 40, 30, 20 and 12 tooth gears and 3 bushings. The 12 tooth motor spindle has a hole diameter of 2mm, where the 40, 30, 20 tooth gears all have a hole diameter of 3/16".

  • CAD$12.00 In Stock

    This pack of associated gear and belt comes with a total of 80 pieces. Theses gears are perfect for making your own little gearbox. 

  • CAD$5.25 In Stock

    This 16 teeth gear has a center diameter of 4mm allowing you to connect it to any 4mm shafts. The gear can be tighten using the M3 set screw. This gear is made with anodized aluminum to minimize any rusting.  Documents:Dimensional Drawing

  • CAD$8.50 In Stock

    This 48 teeth gear has a center diameter of 8mm allowing you to connect to any 8mm shafts. The gear can be mounted with M4 hardware using our 4mm Mounting Hub. This gear is made with anodized aluminum to minimize any rusting.  Documents:Dimensional Drawing

  • CAD$8.50 In Stock

    This 80 teeth gear has a center diameter of 8mm allowing you to connect to any 8mm shafts. The gear can be mounted with M4 hardwares using our 4mm Mount Hub. This gear is made with anodized aluminum to minimize any rusting.  Documents:Dimensional Drawing

  • CAD$6.00 In Stock

    These fine drive belt are made with rubber which can be used as engine drive belts for small DIY cars. This pack of drive belt consists of an assortment of 30mm to 120mm belts.

  • CAD$4.00 Out of stock
    Out of stock

    Timing belts are a fantastic way to transfer rotational motion into linear motion and these GT2 belts are excellent for the task. Often used for precision 3D printers and CNC machines. This belt is 280mm in length and 6mm in width with 2mm pitch. It comes in a loop but you can of course cut it down if you need a shorter length.

  • CAD$21.50 In Stock

    Timing belts are a fantastic way to transfer rotational motion into linear motion and these GT2 belts are excellent for the task. Often used for precision 3D printers and CNC machines. This belt is 1164mm long with 2mm pitch and 6mm wide. It comes in a loop but you can of course cut it down if you need a shorter length.

  • CAD$19.00 In Stock

    Timing belts are a fantastic way to transfer rotational motion into linear motion and these GT2 belts are excellent for the task. Often used for precision 3D printers and CNC machines. This belt is 2004mm long with 2mm pitch and 6mm wide. It comes in a loop but you can of course cut it down if you need a shorter length.

  • CAD$54.00 In Stock

    Timing belts are a fantastic way to transfer rotational motion into linear motion and these GT2 belts are excellent for the task. Often used for precision 3D printers and CNC machines. This belt is 5000mm long with 2mm pitch and 8mm wide. It comes in a loop but you can of course cut it down if you need a shorter length.

No products

To be determined Shipping
CAD$0.00 Total

Check out