Stepper Motor

There are 13 products.

  • CAD$14.00 In Stock

    The A4988 Stepper Motor Driver is a microstepping bipolar stepper motor driver. The A4988 Stepper Moto Driver is able to drive a stepper motor from 8 to 35V with a continuous current of 1A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient additional cooling). This A4988 driver also features adjustable current...

  • CAD$14.25 In Stock

    Black Edition A4988 stepper motor driver carrier is a higher-performance drop-in replacement for the original A4988 stepper motor driver carrier. It features a four-layer PCB for better thermal performance, allowing the A4988 microstepping bipolar stepper motor driver to deliver approximately 20% more current than our two-layer (green) version. Like our...

  • CAD$14.25 In Stock

    This breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver features adjustable current limiting, over-current and over-temperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 V to 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2...

  • CAD$10.50 In Stock

    This is a breakout board for TI’s DRV8834 microstepping bipolar stepper motor driver. It has a pinout and interface that are nearly identical to those of our A4988 carriers, so it can be used as a drop-in replacement for those boards in many applications. The DRV8834 operates from 2.5–10.8 V, allowing stepper motors to be powered with voltages that are...

  • CAD$13.00 In Stock

    The EasyDriver is a simple to use stepper motor driver that can driver up to about 750mA per phase of a bi-polar stepper motor. EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire...

  • CAD$24.95 In Stock

    Each Big Easy Driver can drive up to a max of 2A per phase of a bi-polar stepper motor. It is a chopper microstepping driver which defaults to 16 step microstepping mode. It can take a maximum motor drive voltage of around 30V, and includes on-board 5V/3.3V regulation, so only one supply is necessary. Although this board should be able to run most systems...

  • CAD$5.15 In Stock

    This ULN2003 Unipolar Stepper Motor Driver uses the ULN2003 darlington transistor array to drive a unipolar stepper motor. The ULN2003 driver can drive between 5 to 12V at 0.5A per phase.

  • CAD$35.95 In Stock

    The CNC Shield makes it really simple to integrate CNC projects with the Arduino. You can add up to 4x A4988 stepper motor drivers to the CNC shield allowing for independent control of 4 bi-polar stepper motors. 

  • CAD$35.95 In Stock

    The RAMPS (RepRap Arduino Mega Pololu Shield) is an all-in-one design to fit the necessary components for a 3D printer into one plug in shield. The plug in shield design includes plug in stepper drivers and extruder control electronics sockets for easy service, part replacement, upgrade-ability and expansion. Ramps boards are the heart of most DIY 3D...

  • CAD$11.99 In Stock

    This motor driver shield can drive up to 4 DC motor with 2 servo motors or 2 stepper motors with 2 servo motors. This motor driver shield uses 2x L293D motor controller chip with a 74HC595 shift register for all of its functions. 

  • CAD$35.85 In Stock

    The Arduino Motor Shield is based on the L298, which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your Arduino board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among...

  • CAD$39.95 In Stock

    This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Since the Raspberry Pi does not have a lot of PWM pins, we use a fully-dedicated PWM driver chip onboard to both control motor direction and speed. This chip handles all the motor and speed controls over I2C. Only two pins...

  • CAD$26.50 In Stock

    A Feather board without ambition is a Feather board without FeatherWings! This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top or bottom of your Feather board...

No products

To be determined Shipping
CAD$0.00 Total

Check out