Product Description
Features:
- Communication Range: 10M
- Supported Baud Rate: 9600, 19200, 38400, 57600, 115200, 230400, 460800bps
- UART Interface
- Default Settings:
- Baud Rate: 38400
- Data Bits: 8
- Stop Bit: 1
- Parity: No Parity
- Pin Code: 0000
Documents:
Arduino, Arduino Bluetooth, Microcontrollers, Wireless & IoT, Bluetooth
HC-05 Bluetooth Shield
ARDBE-001108The HC-05 Bluetooth Shield is an easy way to connect the Arduino to any Bluetooth device. The HC-05 Bluetooth Module is a v2.0+EDR (Enhanced Data Rate) Bluetooth which uses a2.4GHz radio transceiver with 3Mbps modulation.
$21.95 |
Frequently Bought Together…
- Wireless & IoT, Bluetooth
HC-05 Bluetooth Module
This Bluetooth is a Bluetooth V2.0+EDR 3Mbps modulation with complete 2.4GHz radio transceiver. This Bluetooth module features a single chip Bluetooth system with CMOS technology and with AFH (Adaptive Frequency Hopping). It can be configured to either Master, Slave or Loopback modes. This Bluetooth module can connect or be connected to any device supporting SPP protocol.
Part Number: PROBT-000005 - Arduino, Microcontrollers
ATmega328 AVR Dev Board
This board is based on the ATmega328 microcontroller. This board shares the same form factor and functionally as the Arduino Uno Rev3. Some key features of this board includes 14 digital I/O of which 6 has PWM output, 6 analog input, 16MHz clock speed, and USB interface.
Note: This is an ATmega328 microcontroller board and is not a product from Arduino.
Part Number: CARDU-031366 - Breadboard Cables, Cables & Connectors, JR Dupont, Male to Female Jumper Wires, Raspberry Pi, Raspberry Pi Cables & Connectors, Raspberry Pi Prototyping
40 Pin (M-F) Splittable Jumper Wire
Breadboard Cables, Cables & Connectors, JR Dupont, Male to Female Jumper Wires, Raspberry Pi, Raspberry Pi Cables & Connectors, Raspberry Pi Prototyping40 Pin (M-F) Splittable Jumper Wire
This is a set of 40 pin splittable jumper wires. Each jumper wire has a length of 200mm (8 inches) and comes with both male and female ends. This kind of flexible jumper wire is perfect for breadboard use as it fits perfectly in the breadboard.
Part Number: CONCG-400010 - Arduino, Microcontrollers
Arduino Uno Rev3
The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
Part Number: ARDDU-031366
Customers Also Viewed
- Arduino, Arduino Motor Drivers, Microcontrollers, Motors, Gear Motors, Servo Motors, Stepper Motors
4 Channel Motor Shield – 1.2A
Arduino, Arduino Motor Drivers, Microcontrollers, Motors, Gear Motors, Servo Motors, Stepper Motors4 Channel Motor Shield – 1.2A
This motor driver shield can drive up to 4 DC motor with 2 servo motors or 2 stepper motors with 2 servo motors. This motor driver shield uses 2x L293D motor controller chip with a 74HC595 shift register for all of its functions.
Part Number: ARDME-002930 - Arduino, Microcontrollers
Arduino Due
The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU. It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button.
Part Number: ARDDU-040062 - Arduino, Arduino Relays, Microcontrollers, Switches & Relays, DC Relays
4 Channel Relay Shield
This 4 Channel Relay Shield is an easy way to control high voltage applications with the Arduino. The maximum switching power for each relay is 70W. You can directly control this shield with the Arduino digital I/Os with an external 9V DC supplty.
Part Number: ARDRL-015841 - Arduino, Arduino SD Storage, Microcontrollers, Wireless & IoT, XBee Radios
Arduino Proto Wireless Shield
Arduino, Arduino SD Storage, Microcontrollers, Wireless & IoT, XBee RadiosArduino Proto Wireless Shield
The Arduino Wireless Proto Shield is a great way to prototype wireless applications thanks to its XBee(TM) compatible socket, prototyping area and SD card connector.You can use the wireless module from Digi to create a network of Arduino boards, solder parts to the prototyping area to create your project, and use the sd card to store data you can then easily transfer to a computer.
Part Number: ARDXB-000064
